View PC924L0YSZ0F_1940157.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

pc924l0nsz0f series 1. recognized by ul1577 (double protection isolation), file no. e64380 (as model no. pc924l ) 2. approved by vde, din en60747-5-2 ( ? ) (as an option), file no. 40008898 (as model no. pc924l ) 3. package resin : ul flammability grade (94v-0) ( ? ) din en60747-5-2 : successor standard of din vde0884 features agency approvals/compliance 1. igbt/mosfet gate drive for inverter control applications gate drive dip 8 pin ? opic photocoupler 1. 8 pin dip package 2. double transfer mold package (ideal for flow soldering) 3. built-in direct drive circuit for igbt drive (i o1p , i o2p : 0.6a) 4. wide operating supply voltage range (v cc : 15 to 30v
5. high noise immunity due to high instantaneous common mode rejection voltage (cm h : min. ? 15kv/ s, cm l : min. 15kv/ s) 6. high isolation voltage between input and output (v iso(rms) : 5.0 kv) 7. lead-free and rohs directive compliant description pc924l0nsz0f series contains an ired optically coupled to an opic chip. it is packaged in a 8 pin dip, available in smt gullwing lead form option. input-output isolation voltage(rms) is 5.0kv. cmr is min. 15kv/ s. 1 sheet no.: d2-a06102en date jun. 30. 2005 ?sharp corporation notice the content of data sheet is subject to change without prior notice. in the absence of confirmation by device specification sheets, sharp takes no responsibility for any defects that may occur in equipment using any sharp devices shown in catalogs, data books, etc. contact sharp in order to obtain the latest device specification sheets before usin g any sharp device. pc924l0nsz0f series ? "opic"(optical ic) is a trademark of the sharp corporation. an opic consists of a light-detecting element and a signal-processi ng circuit integrated onto a single chip.
internal connection diagram truth table 8 7 6 5 1 2 3 4 1 2 3 4 5 6 7 8 interface amp. anode tr.1 tr.2 cathode nc nc gnd o 1 o 2 v cc 2 sheet no.: d2-a06102en outline dimensions (unit : mm) 1. through-hole [ex. pc924l0nsz0f ] 2. through-hole (vde option) [ex. pc924l0yiz0f ] product mass : approx. 0.55g product mass : approx. 0.55g pc924l 2.54 0.25 8 7 6 5 primary side mark 6.5 0.5 0.85 0.2 1.2 0.3 9.66 0.5 3.5 0.5 0.5 0.1 0.5 typ. 1 2 3 4 3.05 0.5 3.4 0.5 : 0 to 13 ? 7.62 0.3 0.26 0.1 epoxy resin date code pc924l 4 vde identification mark 2.54 0.25 8 7 6 5 primary side mark 6.5 0.5 0.85 0.2 1.2 0.3 9.66 0.5 3.5 0.5 0.5 0.1 0.5 typ. 1 2 3 4 3.05 0.5 3.4 0.5 : 0 to 13 ? 7.62 0.3 0.26 0.1 epoxy resin date code pc924l0nsz0f series input on off o 2 terminal output high level low level tr.1 on off tr.2 off on
3 sheet no.: d2-a06102en 3. smt gullwing lead-form [ex. pc924l0nip0f ] 4. smt gullwing lead-form (vde option) [ex. pc924l0yip0f ] product mass : approx. 0.51g plating material : sncu (cu : typ. 2%) product mass : approx. 0.51g pc924l 0.85 0.2 1.2 0.3 primary side mark 7 8 6 5 4 6.5 0.5 1 2 3 2.54 0.25 3.5 0.5 1.0 + 0.4 ? 0 0.26 0.1 epoxy resin 10.0 + 0 ? 0.5 1.0 + 0.4 ? 0 0.35 0.25 7.62 0.3 9.66 0.5 date code pc924l 4 0.85 0.2 1.2 0.3 7 8 6 5 4 6.5 0.5 vde identification mark 1 2 3 2.54 0.25 3.5 0.5 1.0 + 0.4 ? 0 0.26 0.1 epoxy resin 10.0 + 0 ? 0.5 1.0 + 0.4 ? 0 0.35 0.25 7.62 0.3 9.66 0.5 date code primary side mark pc924l0nsz0f series (unit : mm)
date code (3 digit) a.d. 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 mark a b c d e f h j k l m n mark p r s t u v w x a b c mark 1 2 3 4 5 6 7 8 9 o n d month january february march april may june july august september october november december a.d 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2nd digit month of production mark 1 2 3 4 5 week 1st 2nd 3rd 4th 5.6th 3rd digit week of production 1st digit year of production 4 repeats in a 20 year cycle sheet no.: d2-a06102en pc924l0nsz0f series country of origin japan rank mark there is no rank mark indicator.
sheet no.: d2-a06102en electro-optical characteristics * 7 parameter symbol min. typ. max. unit input forward voltage t a = 25?c, i f = 0.2ma reverse current terminal capacitance t a = 25?c, v = 0, f = 1khz output supply voltage ? o 1 low level output voltage o 2 high level output voltage o 2 low level output voltage o 1 leak current o 2 leak current high level supply current low level supply current v cc = 24v, i f = 0 transfer characteristics t a = 25?c, v cc = 24v v cc = 24v isolation resistance rise time fall time instantaneous common mode rejection voltage (high level output) t a = 25?c, v cm = 1.5kv(p-p) instantaneous common mode rejection voltage (low level output) t a = 25?c, v cm = 1.5kv(p-p) v v a pf v v v v a a ma ma ma ma ? s s s s kv/ s kv/ s " low high " input threshold current t a = 25?c, i f = 20ma t a = 25?c, v r = 4v v cc = 24v, i f = 10ma t a = 25?c, v cc = 24v, i f = 10ma ? ? ? 15 ? 20 ? ? ? ? ? 5 10 10 ? ? ? ? ? 15 15 0.6 1.0 0.6 ? 10 250 30 0.4 ? 0.8 500 500 3.0 3.0 ? 0.5 0.5 ? ? 1.4 7.0 10.0 2.0 2.0 conditions "low high" propagation delay time "high low" propagation delay time response time v f1 v f2 i r c t v cc v o1l v o2h v o2l i o1l i o2l i cch i ccl i flh r iso t plh t phl t r t f cm l cm h v cc1 = 12v, v cc2 = ? 12v i o1 = 0.1a, i f = 10ma v cc = v o1 = 24v, i o2 = ? 0.1a, i f = 10ma v cc = 24v, i o2 = 0.1a, i f = 0 v cc = v o1 = 35v, i f = 0 v cc = v o2 = 35v, i f = 10ma r g = 47 ? , c g = 3 000pf i f = 10ma, v cc = 24v, ? v o2h = 2.0v i f = 0, v cc = 24v, ? v o2l = 2.0v *9 *9 t a = 25?c, dc500v, 40 to 60%rh ? 30 ? 0.2 22 0.5 ? ? 1.3 1.3 ? 10 11 0.2 0.2 1.2 0.9 4.0 1.0 1.0 ? ? *8 (unless otherwise specified t a = t opr ) *7 it shall connect a by-pass capacitor of 0.01 f or more between v cc (pin 8 ) and gnd (pin 7 ) near the device, when it measures the transfer characteristics and the output side characteristics *8 i flh represents forward current when output goes from "low" to "high" *9 o 2 output terminal is set to open absolute maximum ratings parameter symbol rating unit input forward current ma reverse voltage v output supply voltage v o 1 output current a a o 2 output current a a o 1 output voltage v power dissipation mw total power dissipation mw operating temperature ?c storage temperature ?c i f v r v cc i o1 i o1p i o2 i o2p v o1 p o p tot v iso (rms) t opr t stg t sol ?c *2 *2 *1 o 1 peak output current *3 o 2 peak output current *5 *4 isolation voltage soldering temperature *1 the derating factors of a absolute maximum ratings due to ambient temperature are shown in fig.10 *2 pulse width 0.15 s, duty ratio : 0.01 *3, 4 the derating factors of a absolute maximum ratings due to ambient temperature are shown in fig.11 *5 ac for 1minute, 40 to 60%rh, f = 60hz *6 for 10s 25 6 35 0.1 0.6 0.1 0.6 35 500 550 5.0 ? 40 to + 100 ? 55 to + 125 270 kv *6 (t a = 25?c) 5 pc924l0nsz0f series
sheet no.: d2-a06102en model line-up pc924l0nsz0f PC924L0YSZ0F ?????? approved pc924l0niz0f pc924l0yiz0f pc924l0nip0f pc924l0yip0f lead form package model no. din en60747-5-2 sleeve taping through-hole 50pcs/ sleeve 1 000pcs/ reel smt gullwing ?????? approved ?????? approved 6 please contact a local sharp sales representative to inquire about production status. pc924l0nsz0f series
sheet no.: d2-a06102en fig.6 test circuit for high level / low level supply current fig.5 test circuit for o 2 leak current 7 pc924l0nsz0f series fig.1 test circuit for o 1 low level output voltage fig.2 test circuit for o 2 high level output voltage fig.3 test circuit for o 2 low level output voltage fig.4 test circuit for o 1 leak current v i f v o1l v cc1 v cc2 1 2 8 5 6 7 i o1 v i f i o2 v o2h v cc 1 2 8 5 6 7 v v o2l v cc i f 1 2 8 5 6 7 i o2 a v cc i f i o1l 1 2 8 5 6 7 a v cc i o2l i f 1 2 8 5 6 7 a v cc i cc i f 1 2 8 5 6 7
sheet no.: d2-a06102en fig.9 test circuit for instantaneous common mode rejection voltage 8 pc924l0nsz0f series fig.7 test circuit for "low high" input threshold current fig.8 test circuit for response time v i f v cc variable 1 2 8 5 6 7 v cc c g r g v out v in duty ratio 50% v in wave form v out wave form t plh t phl 50% 90% 50% 10% t r t f t r = t f = 0.01 s pulse width 5 s 1 2 8 5 6 7 v sw b a gnd gnd v cc v o2 + ? v cm v cm (peak) v cm wave form cm h , v o2 wave form sw at a, i f = 10ma v o2h ? v o2h ? v o2l v o2l cm l , v o2 wave form sw at b, i f = 0 1 2 8 5 6 7
sheet no.: d2-a06102en fig.15 o 1 low level output voltage vs. o 1 output current fig.14 "low high" relative input threshold current vs. ambient temperature fig.12 forward current vs. forward voltage fig.13 "low high" relative input threshold current vs. supply voltage 9 pc924l0nsz0f series fig.10 forward current vs. ambient temperature fig.11 power dissipation vs. ambient temperature 60 50 40 30 20 10 0 forward current i f (ma) ambient temperature t a ( c) ? 25 0 25 50 75 100 125 ? 40 forward voltage v f (v) forward current i f (ma) 0.5 0.75 1 1.25 1.5 1.75 2 1 10 100 0.1 75 c 25 c 0 c t a = 100 c 50 c ? 40 c supply voltage v cc (v) relative input threshold current (%) 15 18 21 24 27 30 70 80 90 100 110 120 t a = 25?c value of v cc = 24v assume 100 ambient temperature t a ( c) relative input threshold current (%) ? 40 ? 20 0 20 40 60 80 100 60 80 100 120 140 160 v cc = 24v i flh = 100% at t a = 25?c 3 2 1 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 t a = 25 c v cc1 = 12v v cc2 = ? 12v i f = 10ma o 1 low level output voltage v o1l (v) o 1 output current i o1 (a) power dissipation po, p tot (mw) 0 100 200 300 400 500 600 p tot p o ambient temperature t a ( c) ? 25 0 25 50 75 100 125 ? 40
sheet no.: d2-a06102en fig.18 o 2 high level output voltage vs. supply voltage fig.19 o 2 high level output voltage vs. ambient temperature fig.20 o 2 low level output voltage vs. o 2 output current 10 pc924l0nsz0f series fig.17 o 2 output voltage drop vs. o 2 output current fig.16 o 1 low level output voltage vs. ambient temperature fig.21 o 2 low level output voltage vs. ambient temperature ? 40 ? 20 0 20 4 06080100 0.3 0.25 0.2 0.15 0.1 0.05 0 ambient temperature t a (?c) o 1 low level output voltage v o1l (v) v cc1 = 12v v cc2 = ? 12v i f = 10ma i o2 = 0.1a ambient temperature t a ( c) ? 40 ? 20 0 20 40 60 80 100 20 21 22 23 24 o 2 high level output voltage v o2h (v) v cc = 24v i f = 10ma i o2 nearly = 0a i o2 = ? 0.1a 3 2 1 0 0.0 0.3 0.1 0.2 0.6 0.4 0.5 o 2 low level output voltage v o2l (v) o 2 output current i o2 (a) t a = 25 c v cc = v o1 = 24v i f = 0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 ? 40 ? 20 0 20 4 06080100 ambient temperature t a ( c) o 2 low level output voltage v o2l (v) v cc = 24v i f = 0 i o2 = 0.1a supply voltage v cc (v) 15 18 21 24 27 30 12 15 18 21 24 27 30 o 2 high level output voltage v o2h (v) t a = 25 c i f = 10ma 0 ? 5 ? 4 ? 3 ? 2 ? 1 0.0 0.1 0.2 0.3 0.4 0.5 0.6 high output voltage drop (v o2h -v cc ) (v) o 2 output current i o2 (a) t a = 25 c v cc = v o1 = 24v i f = 10ma
sheet no.: d2-a06102en fig.27 propagation delay time vs. ambient temperature fig.26 propagation delay time vs. forward current fig.24 high level supply current vs. ambient temperature fig.25 low level supply current vs. ambient temperature fig.22 high level supply current vs. supply voltage fig.23 low level supply current vs. supply voltage 11 remarks : please be aware that all data in the graph are just for reference and not for guarantee. pc924l0nsz0f series 3 0 0.5 1 1.5 2 2.5 high level supply current i cch (ma) 15 18 21 24 27 30 supply voltage v cc (v) t a = 25 ? c i f = 10ma low level supply current i ccl (ma) 15 18 21 24 27 30 supply voltage v cc (v) 3 0 0.5 1 1.5 2 2.5 t a = 25?c i f = 0 v cc = v o1 = 24v r g = 47 ? c g = 3 000pf i f = 10ma 0.5 1 1.5 2 2.5 0 propagation delay time t phl , t plh ( s) t plh t phl ? 40 ? 20 0 20 4 06080100 ambient temperature t a ( ? c) 2.5 0.5 1 1.5 2 0 0510 15 20 25 forward current i f (ma) propagation delay time t phl , t plh ( s) v cc = v o1 = 24v r g = 47 ? c g = 3 000pf t a = 85 ? c 85 ? c ? 40 ? c ? 40 ? c 25 ? c 25 ? c t phl t plh high level supply current i cch (ma) v cc = 24v i f = 10ma ? 40 ? 20 0 20 4 06080100 ambient temperature t a ( ? c) 3 0 0.5 1 1.5 2 2.5 low level supply current i ccl (ma) v cc = 24v i f = 0 ? 40 ? 20 0 20 4 06080100 ambient temperature t a ( ? c) 3 0 0.5 1 1.5 2 2.5
sheet no.: d2-a06102en 12 pc924l0nsz0f series design considerations transistor of detector side in bipolar configuration may be damaged by static electricity due to its minute design. when handling these devices, general countermeasure against static electricity should be taken to avoid breakdown of devices or degradation of characteristics. notes about static electricity in order to stabilize power supply line, we should certainly recommend to connect a by-pass capacitor of 0.01 f or more between v cc and gnd near the device. in case that some sudden big noise caused by voltage variation is provided between primary and secondary terminals of photocoupler some current caused by it is floating capacitance may be generated and result in false operation since current may go through ired or current may change. if the photocoupler may be used under the circumstances where noise will be generated we recommend to use the bypass capacitors at the both ends of ired. the detector which is used in this device, has parasitic diode between each pins and gnd. there are cases that miss operation or destruction possibly may be occurred if electric potential of any pin becomes below gnd level even for instant. therefore it shall be recommended to design the circuit that electric potential of any pin does not become below gnd level. this product is not designed against irradiation and incorporates non-coherent ired. this photocoupler is dedicated to the use for igbt or mosfet gate drive. please do not use this for the other application. as mentioned below, when the input is on, if dc load (resistor etc.) is connected between o 2 output pin 6 and gnd pin 7 and if the electric potential v o2 goes approx. 2v below than electric potential v cc pin 8 continuously, supply current i cc may flow more than usually and go beyond power dissipation. design guide recommended operating conditions parameter forward current supply voltage min. typ. ? ? ? max. 20 30 unit ma v symbol i f v cc operating temperature 70 14 15 ? 40 ?c t opr v cc 2v or more i f 1 2 8 5 6 7 a
sheet no.: d2-a06102en ? for additional design assistance, please review our corresponding optoelectronic application notes. 13 pc924l0nsz0f series degradation in general, the emission of the ired used in photocouplers will degrade over time. in the case of long term operation, please take the general ired degradation (50% degradation over 5 years) into the design consideration. please decide the input current which become 2 times of max. i flh . recommended foot print (reference) 2.54 2.54 1.7 2.2 8.2 2.54 (unit : mm)
sheet no.: d2-a06102en manufacturing guidelines reflow soldering: reflow soldering should follow the temperature profile shown below. soldering should not exceed the curve of temperature profile and time. please don't solder more than twice. soldering method flow soldering : due to sharp's double transfer mold construction submersion in flow solder bath is allowed under the below listed guidelines. flow soldering should be completed below 270?c and within 10s. preheating is within the bounds of 100 to 150?c and 30 to 80s. please don't solder more than twice. hand soldering hand soldering should be completed within 3s when the point of solder iron is below 400?c. please don't solder more than twice. other notices please test the soldering method in actual condition and make sure the soldering works fine, since the impact on the junction between the device and pcb varies depending on the tooling and soldering conditions. 14 1234 300 200 100 0 0 (?c) terminal : 260?c peak ( package surface : 250?c peak) preheat 150 to 180?c, 120s or less reflow 220?c or more, 60s or less (min) pc924l0nsz0f series
sheet no.: d2-a06102en solvent cleaning: solvent temperature should be 45?c or below immersion time should be 3 minutes or less ultrasonic cleaning: the impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time, size of pcb and mounting method of the device. therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of mass production. recommended solvent materials: ethyl alcohol, methyl alcohol and isopropyl alcohol in case the other type of solvent materials are intended to be used, please make sure they work fine in actual using conditions since some materials may erode the packaging resin. cleaning instructions this product shall not contain the following materials. and they are not used in the production process for this product. regulation substances : cfcs, halon, carbon tetrachloride, 1.1.1-trichloroethane (methylchloroform) specific brominated flame retardants such as the pbbos and pbbs are not used in this product at all. this product shall not contain the following materials banned in the rohs directive (2002/95/ec). ?ead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (pbb), polybrominated diphenyl ethers (pbde). presence of odc 15 pc924l0nsz0f series
sheet no.: d2-a06102en package specification 16 12.0 6.7 5.8 10.8 520 2 sleeve package package materials sleeve : hips (with anti-static material) stopper : styrene-elastomer package method max. 50 pcs. of products shall be packaged in a sleeve. both ends shall be closed by tabbed and tabless stoppers. the product shall be arranged in the sleeve with its primary side mark on the tabless stopper side. max. 20 sleeves in one case. sleeve outline dimensions (unit : mm) pc924l0nsz0f series
sheet no.: d2-a06102en 17 tape and reel package package materials carrier tape : a-pet (with anti-static material) cover tape : pet (three layer system) reel : ps carrier tape structure and dimensions f k e i d j g b h h a c dimensions list (unit : mm) a 16.0 0.3 b 7.5 0.1 c 1.75 0.1 d 12.0 0.1 e 2.0 0.1 h 10.4 0.1 i 0.4 0.05 j 4.2 0.1 k 10.2 0.1 f 4.0 0.1 g 1.5 + 0.1 ? 0 5? max. a c e g f b d dimensions list (unit : mm) a 330 b 17.5 1.5 c 100 1.0 d 13 0.5 e 23 1.0 f 2.0 0.5 g 2.0 0.5 pull-out direction [packing : 1 000pcs/reel] reel structure and dimensions direction of product insertion pc924l0nsz0f series
?the circuit application examples in this publication are provided to explain representative applications of sharp devices and are not intended to guarantee any circuit design or license any intellectual property rights. sharp takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of sharp's devices. ?contact sharp in order to obtain the latest device specification sheets before using any sharp device. sharp reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. manufacturing locations are also subject to change without notice. ?observe the following points when using any devices in this publication. sharp takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) the devices in this publication are designed for use in general electronic equipment designs such as: --- personal computers --- office automation equipment --- telecommunication equipment [terminal] --- test and measurement equipment --- industrial control --- audio visual equipment --- consumer electronics (ii) measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when sharp devices are used for or in connection with equipment that requires higher reliability such as: - -- transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- traffic signals --- gas leakage sensor breakers --- alarm equipment --- various safety devices, etc. (iii) sharp devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- space applications --- telecommunication equipment [trunk lines] --- nuclear power control equipment - -- medical and other life support equipment (e.g., scuba). ?if the sharp devices listed in this publication fall within the scope of strategic products described in the foreign exchange and foreign trade law of japan, it is necessary to obtain approval to export such sharp devices. ?this publication is the proprietary product of sharp and is copyrighted, with all rights reserved. under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp. express written permission is also required before any use of this publication may be made by a third party. ?contact and consult with a sharp representative if there are any questions about the contents of this publication. 18 sheet no.: d2-a06102en important notices pc924l0nsz0f series [e232]

▲Up To Search▲

Price & Availability of PC924L0YSZ0F

	To Download PC924L0YSZ0F Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .